Full 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the truck arrives.
Before
After
Before
After
Before
AfterSensor Calibration in Bee Cave, TX
If your garage door is reversing for no apparent reason or refusing to close unless you hold the wall button down, you likely need professional sensor calibration. In Bee Cave, TX, sensor misalignment is the single most common reason a garage door stops working, and we can typically resolve this issue in a single visit with a quick, precise adjustment. If you need help now, call us at (737) 221-2436 to get your door moving again.
Garage door safety sensors operate on a simple infrared beam. If that beam is broken, blocked, or slightly off-kilter, the opener assumes there is an obstruction in the path of the door and refuses to close for safety reasons. At Otto’s Garage Door, we have been providing Garage Door Repair in Bee Cave since 2004. We don’t just push the sensor back into place; we ensure the alignment is locked, the mounting brackets are secure, and the wiring isn’t frayed from years of Texas heat cycles. Because we are locally owned and owner-operated, I will be the one answering your call, and I will be the one standing in your driveway to fix it.
When You Need Sensor Calibration
You do not always need a full repair when your door acts up. Often, the sensors just need a nudge or a cleaning. However, knowing when it is a simple calibration issue versus a failing logic board or broken wire saves you time and money. Here is what we look for when we arrive at your home in Bee Cave:
- The door reverses immediately: If the door starts to close and then immediately springs back up, the sensors are likely misaligned or blocked by debris.
- The light on the motor unit is flashing: Most openers, like LiftMaster or Craftsman, have a diagnostic light on the motor unit. If it flashes a specific number of times when you try to close the door, it is signaling a sensor error.
- The wall button works, but the remote does not: Sometimes a sensor issue prevents the remote signal from completing the close cycle, forcing you to hold the wall button to override the safety feature.
- Visible physical damage: If a lawnmower, car tire, or kid’s bike has bumped the sensor bracket, it is no longer pointing directly at its partner across the garage opening.
- Sunlight interference: In some Bee Cave homes, the afternoon sun hits the sensor directly, blinding the infrared beam. We can adjust the angle of the sensor to prevent this common, frustrating issue.
If you are experiencing any of these, call (737) 221-2436. We provide upfront pricing before we ever head out to your address.
Our Sensor Calibration Process
I handle sensor calibration with the same attention to detail as Spring Repair. A door is a heavy piece of equipment, and those sensors are the only thing stopping it from closing on a vehicle or a person. Here is how we handle it when we come out to your property:
- Visual Inspection: We start by checking the wiring. Vibration from the door operation can loosen connections over years of use, and rodents in our area sometimes chew on the low-voltage wires running along the garage walls.
- Bracket Alignment: We check the mounting brackets. If they are loose or bent, the sensors will never hold an alignment. We tighten the hardware and ensure the sensors are level with each other.
- Infrared Beam Alignment: We use a precise adjustment technique to ensure the infrared beam is perfectly centered between the two units. This is where many DIY attempts fall short, as even a millimeter of deviation can cause intermittent failures.
- Cleaning the Lenses: Over time, dust, cobwebs, and moisture can cloud the sensor lenses. We clean them with the correct materials to ensure a clear signal path.
- Safety Test: Finally, we perform a mandatory safety reversal test. We place an object in the path of the door to ensure that as soon as the beam is broken, the door stops and reverses instantly.
If you need expert help with your garage door, you can always reach out to our home office for guidance. We stand behind our work with a 90-Day Done Right Promise, meaning if it is not fixed correctly, I will come back and make it right.
Sensor Calibration Pricing in Bee Cave
Calibration is one of the most affordable services we offer, usually falling into the range of $85 to $150, depending on whether we need to repair frayed wiring or replace a damaged bracket. We believe in upfront pricing, so you will know exactly what you are paying before we arrive. We do not have hidden trip charges if you are located inside our home county.
| Service Type | Estimated Price Range |
|---|---|
| Standard Sensor Alignment & Cleaning | $85 – $110 |
| Wiring Repair & Re-alignment | $110 – $150 |
| Full Sensor Replacement (Parts & Labor) | $150 – $225 |
Remember, we offer a Free Second Opinion on any written estimate you have received from another company. If you have been told you need a new motor when your sensors just need to be aligned, call us at (737) 221-2436. We are honest about what your door actually needs.
FAQs - Sensor Calibration
Can I fix misaligned sensors myself?
Yes, you can often fix them by simply cleaning the lenses or gently pushing the brackets back into alignment until the indicator light on the sensor turns solid. However, if the wiring is damaged or the brackets are bent, you should call a professional for Cable Repair or other service, as improper handling of the garage door system can be dangerous. If you are struggling to get the lights to turn solid, call us at (737) 221-2436 for a quick quote.
Is it cheaper to replace the sensors or the whole opener?
Before considering our Garage Door Repair services for a full replacement, know that it is almost always significantly cheaper to replace just the sensors, which typically cost a fraction of a new motor unit. If your opener is over 15 years old, we might discuss whether it is worth the investment, but for most newer units from brands like Wayne Dalton or Raynor, a sensor swap is a very cost-effective repair. We always provide an honest recommendation based on the condition of your existing equipment.
How do I know if my sensors are failing or if the logic board is broken?
If the sensors are failing, the indicator lights on the sensors themselves will usually be off or blinking; if the logic board on the motor unit is the problem, the sensors will be lit, but the motor will not respond to the signal. Because we have been in business since 2004, we can usually diagnose the difference over a quick phone call. Call (737) 221-2436 and we can troubleshoot it with you.
Do you offer same-day service for sensor issues?
Yes, we prioritize safety-related issues, and a door that will not close is a significant security risk for your home. We are locally owned and owner-operated, which means we do not have a massive dispatch queue to navigate. When you call (737) 221-2436, you are speaking to someone who can get a technician to your door as quickly as possible.
At Otto’s Garage Door, we believe in doing the job right the first time. Whether you need Track Realignment, a simple alignment, or a full system check, we are here to help our neighbors in Bee Cave. We offer a permanent 10% discount for seniors and veterans, and we never charge a trip fee within our home county. Call us today at (737) 221-2436 for a free estimate.
Written by Otto Reinhardt, Owner at Otto’s Garage Door, serving Bee Cave.